Provides receiver battery voltage and signal strength through the Aurora 9's telemetry display (Telemetry support requires 8 or 10 channel XtremeLink® receiver with v3.7 or later firmware).

Support for interfacing Eagletree and Hitec sensors is coming soon! ALL Aurora 9 modules are in-field flashable!

WARNING! The relocation of the antenna requires you drilling a hole through the Aurora 9's transmitter housing plastic. If you do not believe you can do this, then please do not purchase this upgrade!

Kit includes: top mount adapter with 7" pigtail pre-installed and new case back.

Installation information can be found in our vendor area on RCGroups.com.

Replacment case comes with top and bottom halves, with 4 new screws.

Replacment case comes with top and bottom halves, with 4 new screws.

Consisting of one XtremeLink® 2.4GHz transmitter module (internal), adapter plug, and antenna.

SUPPORTS ALL VERSIONS OF EVO FIRMWARE UP TO v3.41!

v3.0 and later of the EVO's transmitter firmware supports Multiplex's "M-Link", which is their 2.4GHz system. Using a new harness assembly and a firmware upgrade, we emulate the M-Link system. This gives you all of the M-Link features, such as ability to do the range test from the front buttons, binding receivers from the front buttons, and even telemetry support. This upgrade package also includes the new top mount antenna adapter and antenna coax. You install the antenna through the top of the transmitter and snap on the antenna connector on our board. This upgrade supports all Multiplex firmware versions up to 3.41, and still supports the older versions if you go backwards in versions.

How to upgrade

Purchase this upgrade, and then send in a copy of your purchase invoice with your original EVO XtremeLink board. We will modify the board and install the new harness, reflash the board, test it all, and send it back with the new antenna system.

Xtreme Power Sytems
Attn: EVO Upgrade
2440 Kiowa Blvd. N. #102
Lake Havasu City, AZ 86403
USA

Not compatible with Futaba 9Z, Futaba surface radios, or Hitec transmitters.

Consisting of one XtremeLink® 2.4GHz transmitter module (internal), adapter plug, and antenna w/ball.

The ultimate tool for checking your power system!

The TattleTale is a tiny and lightweight device that plugs into a empty receiver channel (or through a Y-cable). This device measures the input voltage and displays the lowest voltage threshold that was captured after being powered on. With a programmable acquisition time of 1ms to 100ms, even the shortest voltage sags can be detected!

The TattleTale also monitors your servo signal and immediately reports any "glitch" in the servo output by flashing the multi-colored LED. PPM glitches, failsafes, and even reboots can now be reported!

As a special bonus, the TattleTale can also be a programmable timer, flashing the LED bright white after time has expired. This is great for night flyers!

People have been flying for decades with inadequate power. With the development of 2.4GHz radio systems, power requirements are now being enforced. Don't be caught with a power system that is marginal and risk your aircraft, car, or boat!

Features:

Voltage detection range from 2.1v to 16v
Voltage acquistion every 1ms to 100ms
Receiver glitch/failsafe/reboot detection
Programmable flight timer
Small size: .5" x .75"
Light weight: 1.75g (.062 oz)
Lifetime warranty!

XtremeLink® 2.4GHz 6 channel Nano-T Receiver

The next generation of XtremeLink® 2.4GHz receivers is here!

This top pin receiver is ideal for use in foamies, micro-helis, and anything requiring a tiny and lightweight receiver!

Compatible with all XtremeLink® and iFS brand radio systems.

Specifications:

Size: 1.05" x .71" (27.5mm x 18.25mm)
Weight: .11oz (3.1g)
Voltage: 2.0v - 16v

XtremeLink® 2.4GHz 6 channel Nano-E Receiver

The next generation of XtremeLink® 2.4GHz receivers is here!

This end pin receiver is ideal for use in small gliders and anything requiring a tiny and lightweight receiver! This receiver was designed for "park flyer" type aircraft, but has outstanding range!

Compatible with all XtremeLink® and iFS brand radio systems.

Specifications:

Size: 1.4" x .71" (36.1mm x 18.25mm)
Weight: .124oz (3.5g)
Voltage: 2.0v - 16v

XtremeLink® 2.4GHz 8 channel receiver.

Integrated antenna system.

This device and software allows you to wirelessly change the settings of XtremeLink® receivers and transmitter module! It also allows you to update the firmware of receivers and transmitter modules for those units that are in-field upgradable*.

Software is available for download from our website in the DOWNLOADS section.

Requires a USB type A to mini-b cable (commonly used with cell phones and digital cameras).

Applications for RxDiag, TxDiag, Device Programmer, and spectrum analyzer are currently available. Future applications such as support for flight simulators will be released in the future.

Detailed information can be found on our XDP support page. Click Here

* Only in-field upgradable units can have their firmware updated with this device. All units not capable of in-field updates can not be made to allow in-field updates. In these cases, new hardware is required.

This PC based hardware device and software allows you to wirelessly obtain telemetry data from any XPS receiver and transmitter in real time. The data can also be recorded and played back for later viewing. Information available: receiver battery voltage, transmitter battery voltage, signal strength, frame rate, number of channels in use, servo positions, brown out conditions, and information from any sensor connected (sensors sold separately).

This unit also performs all of the same functions as the Xtreme Device Programmer (XDP).

NOTE: v3.0 of later of the XtremeLink® firmware (both transmitter module and receivers) is required in order to use this product. This upgrade requires the return of your existing hardware to accomplish this. It is not possible to for a user upgrade any existing pre-v3.0 units in-field due to a necessary RF firmware change. Details on how to return your system(s) will be included when you receive this product.

Requires a USB type A to mini-b cable (commonly used with cell phones and digital cameras).

Detailed information can be found on our Telemetry Station support page. Click Here

WARNING! Proper installation of this upgrade is critical! A range test is absolutely required after performing this upgrade!

NOTE: This upgrade will NOT work with the Futaba 9Z or Hitec transmitters!

WARNING! Proper installation of this upgrade is critical! A range test is absolutely required after performing this upgrade!

Dual removable o-rings hold the tool in place. Fits most transmitters.

This plastic piece excepts a standard RP-SMA connector.

Note: This product is available with the connector pre-installed (see part #XPS-MOUNT2). This product was designed to fit connectors firmly, some filing of the connector may be required for proper fit.

This plastic piece has our custom 7" RP-SMA connector pre-installed.

NO RMA IS REQUIRED.

Please ship your damaged/defective product with a copy of your pre-paid XtremeLink Hardware Repair order to:

Xtreme Power Sytems
Attn: Hardware Repair
2440 Kiowa Blvd. N. #102
Lake Havasu City, AZ 86403
USA

Latest firmware version is: v3.9 (Rx), v3.8 (Tx)

V3.x Firmware upgrade. Includes multiple receiver support, full time frequency hopping, and more!

After you purchase this upgrade, you will need to send in all pieces of your XtremeLink system. You must return your transmitter module, receivers, XDP, and telemetry station if you want the full 3.x upgrade.

YOU MUST INCLUDE A COPY OF YOUR RECEIPT FOR THIS ORDER WITH YOUR ITEMS TO BE UPGRADED!

DO NOT SEND TRANSMITTERS WITH YOUR SYSTEM! THEY WILL BE RETURNED WITHOUT BEING UPGRADED.

NO RMA IS REQUIRED.

Please ship a copy of your order, along with your XtremeLink products to be upgraded to:

Xtreme Power Sytems
Attn: Firmware Upgrade
2440 Kiowa Blvd. N. #102
Lake Havasu City, AZ 86403
USA