Home » XPS Products » XtremeLink® » Receivers
The 5th generation of XtremeLink® 2.4GHz receivers is here! Offering even more range than any previous version!
This end pin receiver is ideal for use in small gliders and anything requiring a tiny and lightweight receiver! However, don't let the size of this receiver fool you - it's a full range receiver! In fact, it has better range than the original 8 and 10 channel receivers we offered.
Supports PWM, PPM, "Xtreme" and "mixed mode" outputs so you can use flight stablizers, helicopter gyro systems, etc. with a single servo wire connection! With an operational voltage of just 1.8 volts (and up to 16v), brown outs are never a concern!
Supports wireless programming through our XDP unit
Compatible with all XtremeLink® and iFS brand radio systems.
Size: 1.4" x .71" (36.1mm x 18.25mm)
Weight: .124oz (3.5g)
Voltage: 1.8v - 16v
This top pin receiver is ideal for use in small gliders and anything requiring a tiny and lightweight receiver! However, don't let the size of this receiver fool you - it's a full range receiver! In fact, it has better range than the original 8 and 10 channel receivers we offered.
Supports PWM, PPM, "Xtreme" and "mixed mode" outputs so you can use flight stabilizers, helicopter gyro systems, etc. with a single servo wire connection! With an operational voltage of just 1.8 volts (and up to 16v), brown outs are never a concern!
Size: 1.05" x .71" (27.5mm x 18.25mm)
Weight: .11oz (3.1g)
Voltage: 1.8v - 16v
The 5th generation of XtremeLink® 2.4GHz receivers is here!
This pin-less receiver is ideal for use in small indoor aircraft where the extra weight of servo pins might be a burden! This is the same receiver as our end pin and top pin versions, so don't let the size of this receiver fool you - it's a full range receiver!
Size: 1.05" x .71" (27.5mm x 18.25mm)
Weight: .039oz (1.1g)
Voltage: 1.8v - 16v
This is the second version of our original version! The X10+ Channel Expander is a small device that acts as a power expander, channel expander, voltage monitor, and failsafe system for different types of receivers that output a serial data stream. So, XPS Nano, Nano II, & RFU, JR DMSS X-Bus (Mode A & Mode B), Futaba SBUS/SBUS2, Graupner HoTT SUMD, JETI UDI, and Spektrum satellite receivers are all supported. ALL types of servos are supported, so ALL receivers will work with ALL servos. You don't need special and expensive servos!
Single or dual receivers can be used with all supported systems!
Input type: serial data stream
Channel outputs: 10 (or 11 with auxiliary port)
Operating voltage: 1.8v - 16v
Servo bus current: >80A
Recognized protocols: Xtreme (fast), Xtreme (slow), JR DMSS X-Bus (Mode A & Mode B), Futaba SBUS/SBUS2, Graupner HoTT SUMD, JETI UDI, Spektrum satellite
Size: 1.25" x 1.4" x .450"
Servo plug spacing: .113"
Weight (top pins): .248oz (7.04g)
Weight (end pins): .275oz (7.79g)
Accessories included: two mounting spacers
Recommended accessories: XPS Serial Link, UltraTwist cables, EC3 harness pair
Click here for accessories.
Click here to see the X10+ manual.
The RFU is a highly sensitive receiver with diversity antennas, offering the absolute best range of our entire product line. This device interfaces directly into our X10+ Channel Expander. It can also output many other protocols, such as Spektrum satellite and Futaba S.BUS, and even a composite PPM data stream.
Output type: serial data stream
Operating voltage: 1.8v - 10v
Output protocols: Xtreme (fast), Xtreme (slow) Futaba SBUS, Spektrum satellite (lowres/hires), PPM (positive/negative)
Antenna lead length: 6.5" (165mm)
Size: 1.13" x 1.04" x .36" (28.8mm x 26.4mm x 9.1mm)
Weight: .3oz (8.49g)
Accessories included: velcro for mounting
Recommeneded accessories: X10+ Channel Expander, UltraTwist cables
Click here for wiring options.
The TattleTale is a tiny and lightweight device that plugs into a empty receiver channel (or through a Y-cable). This device measures the input voltage and displays the lowest voltage threshold that was captured after being powered on. With a programmable acquisition time of 1ms to 100ms, even the shortest voltage sags can be detected!
The TattleTale also monitors your servo signal and immediately reports any "glitch" in the servo output by flashing the multi-colored LED. PPM glitches, failsafes, and even reboots can now be reported!
As a special bonus, the TattleTale can also be a programmable timer, flashing the LED bright white after time has expired. This is great for night flyers!
People have been flying for decades with inadequate power. With the development of 2.4GHz radio systems, power requirements are now being enforced. Don't be caught with a power system that is marginal and risk your aircraft, car, or boat!
Voltage detection range from 2.1v to 16v
Voltage acquistion every 1ms to 100ms
Receiver glitch/failsafe/reboot detection
Programmable flight timer
Small size: .5" x .75"
Light weight: 1.75g (.062 oz)
Replacment case comes with top and bottom halves, with 4 new screws.
This device and software allows you to wirelessly change the settings of XtremeLink® receivers and transmitter module! It also allows you to update the firmware of receivers and transmitter modules for those units that are in-field upgradable*.
Software is available for download from our website in the DOWNLOADS section.
Requires a USB type A to mini-b cable (commonly used with cell phones and digital cameras).
Applications for RxDiag, TxDiag, Device Programmer, and spectrum analyzer are currently available. Future applications such as support for flight simulators will be released in the future.
Detailed information can be found on our XDP support page. Click Here
* Only in-field upgradable units can have their firmware updated with this device. All units not capable of in-field updates can not be made to allow in-field updates. In these cases, new hardware is required.
Fill that empty antenna hole with our Radio Tool! This tool has an attractive name plate (XPS on one side, and XtremeLink® on the other) and a long stem that you can use to bind your receivers!
Dual removable o-rings hold the tool in place. Fits most transmitters.
NO RMA IS REQUIRED.
Just add this REPAIR to your cart. You can continue your shopping or go immediately to check out. You will be paying for return shipping cost only. Once you have completed the order, print a copy of the order receipt.
Please ship your damaged/defective product(s) with the printed copy of your order showing the XtremeLink® Hardware Repair to:
Xtreme Power Systems
Attn: Hardware Repair
3269 Maricopa Ave. Ste. 114-511
Lake Havasu City, AZ 86406
Please note: if you add other items to the shopping cart, we will hold the order and wait until we have received the item(s) to be repaired, and return the repaired item(s) back to you along with the other items you ordered.
Please ship a copy of your upgrade order, along with your XtremeLink® JR module to be upgraded to:
Xtreme Power Sytems
Attn: Firmware Upgrade
1642 McCulloch Blvd. N. #394
Lake Havasu City, AZ 86403
Latest firmware version is: v3.9 (Rx), v3.8 (Tx)
V3.x Firmware upgrade. Includes multiple receiver support, full time frequency hopping, and more!
After you purchase this upgrade, you will need to send in all pieces of your XtremeLink® system. You must return your transmitter module w/antenna, receivers, XDP, and telemetry station if you want the full 3.x upgrade.
YOU MUST INCLUDE A COPY OF YOUR RECEIPT FOR THIS ORDER WITH YOUR ITEMS TO BE UPGRADED!
DO NOT SEND TRANSMITTERS WITH YOUR SYSTEM! THEY WILL BE RETURNED WITHOUT BEING UPGRADED.
Please ship a copy of your order, along with your XtremeLink® products to be upgraded to: