https://www.xtremepowersystems.net/forum/ Tue, 14 Apr 2026 15:24:47 +0000 MyBB https://www.xtremepowersystems.net/forum/showthread.php?tid=168 Tue, 26 Aug 2025 20:19:59 -0400 Fanglacolla]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=168 When I changed to pin and flag and programed it in the X16, it powers off when the pin is installed but the Green Status light Stays ON.  
Would that be normal for using Pin and Flag switching?
   Thank You,]]> When I changed to pin and flag and programed it in the X16, it powers off when the pin is installed but the Green Status light Stays ON.  
Would that be normal for using Pin and Flag switching?
   Thank You,]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=127 Mon, 23 Sep 2024 14:42:37 -0400 Ville]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=127 Don't understand why X16 Mlink flickers a lot with many lost frames. Doesn't matter if I use Mpx Mlink or Radimaster Boxer and their ER receivers.
How should I interpret the LF values that count at a fast rate, what is acceptable? Is there anything I can do to make the green light shine with a steady light and avoid all lost frames?
My X10+ behaves the same. Otherwise, everything works as it should, all the servos move smoothly and well.

/Ville ]]> Don't understand why X16 Mlink flickers a lot with many lost frames. Doesn't matter if I use Mpx Mlink or Radimaster Boxer and their ER receivers.
How should I interpret the LF values that count at a fast rate, what is acceptable? Is there anything I can do to make the green light shine with a steady light and avoid all lost frames?
My X10+ behaves the same. Otherwise, everything works as it should, all the servos move smoothly and well.

/Ville ]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=79 Sun, 06 Aug 2023 06:18:51 -0400 Larry J.]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=79 Is the X16 available and if so, how can I place an order?

Thank You]]> Is the X16 available and if so, how can I place an order?

Thank You]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=73 Sun, 26 Mar 2023 01:20:38 -0400 voyager101]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=73 https://www.xtremepowersystems.net/forum/showthread.php?tid=71 Thu, 19 Jan 2023 04:54:35 -0500 voyager101]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=71 https://www.xtremepowersystems.net/forum/showthread.php?tid=30 Tue, 01 Jun 2021 19:57:49 -0400 XPS]]> https://www.xtremepowersystems.net/forum/showthread.php?tid=30
X16 setup. TX16S. Have set up all ch OK.
Not getting the sequencers I want.
Retracts and doors, Ch 5 on 3 pos switch.
X16 Ports A2 and B2 output from Ch 5.
Servos work OK.

Now to the sequencer: Trigger at 1500.
Tx Ch 5 Sw up Seq#1 triggers doors down. Port A2
Tx Ch 5 Sw up Seq#2 triggers gear down.   Port B2
Not set up yet.
Tx Ch 5 Sw dn Seq#3 triggers gear up.        Port B2
Tx Ch 5 Sw dn Seq#4 triggers doors up.      Port A2

When all sequencers disabled, servos work. Expected.
One enabled, wrong servo works.
Both enabled, nothing works.

So tried duplicating Ch5 as Ch13 in Tx.
Ch 5 Seq#1  doors down. Port A2
Ch 13 Seq#2 gear down.  Port B2
Same thing.  Tx outputs do show in X16.

From reading the X16 manual am I misunderstanding the process?
Quite possible.
Can set it up from the Tx, but reckon that the X16 should do it too.

Cheers,]]>
X16 setup. TX16S. Have set up all ch OK.
Not getting the sequencers I want.
Retracts and doors, Ch 5 on 3 pos switch.
X16 Ports A2 and B2 output from Ch 5.
Servos work OK.

Now to the sequencer: Trigger at 1500.
Tx Ch 5 Sw up Seq#1 triggers doors down. Port A2
Tx Ch 5 Sw up Seq#2 triggers gear down.   Port B2
Not set up yet.
Tx Ch 5 Sw dn Seq#3 triggers gear up.        Port B2
Tx Ch 5 Sw dn Seq#4 triggers doors up.      Port A2

When all sequencers disabled, servos work. Expected.
One enabled, wrong servo works.
Both enabled, nothing works.

So tried duplicating Ch5 as Ch13 in Tx.
Ch 5 Seq#1  doors down. Port A2
Ch 13 Seq#2 gear down.  Port B2
Same thing.  Tx outputs do show in X16.

From reading the X16 manual am I misunderstanding the process?
Quite possible.
Can set it up from the Tx, but reckon that the X16 should do it too.

Cheers,]]>