Provides receiver battery voltage and signal strength through the Aurora 9's telemetry display (Telemetry support requires 8 or 10 channel XtremeLink® receiver with v3.7 or later firmware).

WARNING! The relocation of the antenna requires you drilling a hole through the Aurora 9's transmitter housing plastic. If you do not believe you can do this, then please do not purchase this upgrade!

Kit includes: top mount adapter with 7" pigtail pre-installed and new case back.

Installation information can be found in our vendor area on RCGroups.com.

Consisting of one XtremeLink® 2.4GHz transmitter module (internal), adapter plug, and antenna.

SUPPORTS ALL VERSIONS OF EVO FIRMWARE UP TO v3.56!

v3.0 and later of the EVO's transmitter firmware supports Multiplex's "M-Link", which is their 2.4GHz system. Using a new harness assembly and a firmware upgrade, we emulate the M-Link system. This gives you all of the M-Link features, such as ability to do the range test from the front buttons, binding receivers from the front buttons, and even telemetry support. This upgrade package also includes the new top mount antenna adapter and antenna coax. You install the antenna through the top of the transmitter and snap on the antenna connector on our board. This upgrade supports all Multiplex firmware versions up to 3.56, and still supports the older versions if you go backwards in versions.

How to upgrade

Purchase this upgrade, and then send in a copy of your purchase invoice with your original EVO XtremeLink board. We will modify the board and install the new harness, reflash the board, test it all, and send it back with the new antenna system.

Xtreme Power Sytems
Attn: EVO Upgrade
1642 McCulloch Blvd. N. #394
Lake Havasu City, AZ 86403
USA

Not compatible with Futaba 9Z, Futaba surface radios, or Hitec transmitters.

Internal XtremeLink® 2.4GHz JR11x transmitter module.

Convert your DSM2/DSMX JR11x transmitter to an XtremeLink® 2.4GHz system!

Easy to install. See the manual for installation details!

NOTE: CASES ARE NO LONGER INCLUDED WITH THESE MODULES.

XtremeLink® RFU Diversity Receiver

Compatible with all XtremeLink® and Graupner iFS systems.

The RFU is a highly sensitive receiver with diversity antennas, offering the absolute best range of our entire product line. This device interfaces directly into our X10+ Channel Expander. It can also output many other protocols, such as Spektrum satellite and Futaba S.BUS, and even a composite PPM data stream.

RFU Specifications:

Output type: serial data stream
Operating voltage: 1.8v - 8.5v
Output protocols: Xtreme (fast), Xtreme (slow) Futaba SBUS, Spektrum satellite (lowres/hires), PPM (positive/negative)
Antenna lead length: 6.5" (165mm) Size: 1.13" x 1.04" x .36" (28.8mm x 26.4mm x 9.1mm)
Weight: .3oz (8.49g)
Accessories included: velcro for mounting
Recommeneded accessories: X10+ Channel Expander, UltraTwist cables

Click here for wiring options.

Replacment case comes with top and bottom halves, with 4 new screws.

WARNING! Proper installation of this upgrade is critical! A range test is absolutely required after performing this upgrade!

NOTE: This upgrade will NOT work with the Futaba 9Z or Hitec transmitters!

WARNING! Proper installation of this upgrade is critical! A range test is absolutely required after performing this upgrade!

NEW STYLE - NOW COMES AS A COMPLETE CABLE!

This device and software allows you to change the settings of X10+ Channel Expander and future products from XPS.

Requires a USB type A to mini-b cable (commonly used with cell phones and digital cameras), and JR female to female cable, both not supplied.

Works only with the 'XDP.exe' program in the XDP softrware package.

Detailed information and installation software can be found on our XDP support page. Click Here

XtremeLink® Radio Tool

Fill that empty antenna hole with our Radio Tool! This tool has an attractive name plate (XPS on one side, and XtremeLink® on the other) and a long stem that you can use to bind your receivers!

Dual removable o-rings hold the tool in place. Fits most transmitters.

This plastic piece excepts a standard RP-SMA connector.

Note: This product is available with the connector pre-installed (see part #XPS-MOUNT2). This product was designed to fit connectors firmly, some filing of the connector may be required for proper fit.

NO RMA IS REQUIRED.

Just add this REPAIR to your cart. You can continue your shopping or go immediately to check out. You will be paying for return shipping cost only. Once you have completed the order, print a copy of the order receipt.

Please ship your damaged/defective product(s) in a box (not a flat mailer) with the printed copy of your order showing the XtremeLink® Hardware Repair to:

Xtreme Power Systems
Attn: Hardware Repair
1642 McCulloch Blvd. N. #394
Lake Havasu City, AZ 86403
USA

Please note: if you add other items to the shopping cart, we will hold the order and wait until we have received the item(s) to be repaired, and return the repaired item(s) back to you along with the other items you ordered.

DO NOT SEND COMPLETE RADIO SYSTEMS, INCLUDING A TRANSMITTER WITHOUT EXPRESS PERMISSION FROM XTREME POWER SYSTEMS - OTHERWISE, PACKAGES CONTAINING TRANSMITTERS WILL NOT BE ACCEPTED!

NO RMA IS REQUIRED.

Please ship a copy of your upgrade order, along with your XtremeLink® JR module to be upgraded to:

Xtreme Power Sytems
Attn: Firmware Upgrade
1642 McCulloch Blvd. N. #394
Lake Havasu City, AZ 86403
USA

Latest firmware version is: v3.9 (Rx), v3.8 (Tx)

V3.x Firmware upgrade. Includes multiple receiver support, full time frequency hopping, and more!

After you purchase this upgrade, you will need to send in all pieces of your XtremeLink® system. You must return your transmitter module w/antenna, receivers, XDP, and telemetry station if you want the full 3.x upgrade.

YOU MUST INCLUDE A COPY OF YOUR RECEIPT FOR THIS ORDER WITH YOUR ITEMS TO BE UPGRADED!

DO NOT SEND TRANSMITTERS WITH YOUR SYSTEM! THEY WILL BE RETURNED WITHOUT BEING UPGRADED.

NO RMA IS REQUIRED.

Please ship a copy of your order, along with your XtremeLink® products to be upgraded to:

Xtreme Power Sytems
Attn: Firmware Upgrade
1642 McCulloch Blvd. N. #394
Lake Havasu City, AZ 86403
USA